Lowest prices for Omis doors on the Internet! A 5% discount is guaranteed when ordering. Availability in stock! We are the official representative in Kyiv.
Rating Interior doors Omis Cortex Deco 09 oak amber line
No one has rated this product yet. Be the first :-)
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior ChS - canvas with black glass. Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80 mm and a long legs 25 mm attention! Installation of door leaflets and praisins products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient for installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient when installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient for installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition. Horizontal - emphasizes the refined taste of the owner of the interior. Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient when installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior ChS - canvas with black glass. Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient for installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient for installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient when installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 The canvas is made to order! Cortex Alumo door leaf with mortise for lock and hinges + lock included. The special profile of the box allows you to install platbands almost in the same plane with the canvas, which meets modern trends. The end of the leaf is lined with an aluminum edge, which, in addition to its decorative function, protects the door from mechanical damage. Adjustable 3D hinges included in the door frame kit allow you to precisely adjust the position of the door leaf. The DEVENTER 3967 seal is used, which has improved performance characteristics and is convenient when installing the door block (the head of the screw that secures the frame is hidden under the seal). The door leaf is equipped with an AGB lock (if necessary, it is possible to install a plumbing lock). The door frame is designed for a wall thickness of 100-120 mm (for greater thickness it is necessary to use an additional strip or open the casing). The door frame is cut to 450, holes are drilled for dowels. This allows you to get rid of gaps at the joints between long and short trims
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. The height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening with the use of an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden for an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x34 2000x700x34 2000x800x34 2000x900x34 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition Horizontal - emphasizes the refined taste of the owner of the interior Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
2000x600x40 2000x700x40 2000x800x40 2000x900x40 Cortex is a new design material that was created specifically for those who value cozy, simple and stylish interiors. The coating is resistant to various types of mechanical damage. The doors perfectly resist moisture, are practical to use and do not require special care. Vertical - fills with energy all the elements participating in the composition. Horizontal - emphasizes the refined taste of the owner of the interior. Attention! All measurements must be made by the installer. To select a door leaf, you will need the following data: 1. Opening width (measured at three points and the minimum is selected): for a 600mm wide leaf it should be 680-700mm, for a 700mm wide leaf it should be 780-800mm, for a 800mm wide leaf it should be 880-900mm for for a canvas with a width of 900mm, it should be 980-1000mm 2. Height of the opening (measured at two points and the minimum is selected): For a canvas with a height of 2000mm, it should be 2050-2070mm. To select molded products (box, additional strip and platband), the following data will be required: 1 .Thickness of the opening in which installation is planned (measured at three points and the maximum is selected) 2. Type of frame: Wooden telescopic 80mm: - allows you to cover the thickness of the opening without using an additional strip up to 120mm * - allows you to cover the thickness of the opening using an additional strip "70mm" up to 185mm* - allows you to cover the thickness of the opening with the use of an additional strip "110mm" up to 225mm* Attention! If the thickness of the wall that needs to be covered is greater than indicated above, then you can use several telescopic additional strips (consultation with a manager is required) Wooden extension strip 80mm: - allows cover the thickness of the opening without the use of an additional strip 80mm - allows you to cover the thickness of the opening using an additional strip "100mm" up to 170mm - allows you to cover the thickness of the opening using an additional strip "150mm" up to 220mm Wooden with an extension 100mm: - allows you to cover the thickness of the opening without using an additional strip 100mm- allows you to block the thickness of the opening using the 100mm of the “100mm” to 190mm, allows you to block the thickness of the opening using the additional plan “150mm” up to 240mm 3. The platband: a rectangular width of 70mmmelescopic width of 80mm and a long legs 25 mm attention and attention! products are produced in pre-prepared openings, after interior work has been carried out. * the size is indicated with two trims extended to the maximum
Decorative beams
Smooth cornices
Cornices with ornaments
Concealed lighting cornices
Polyurethane domes
Ceiling tiles
Decorative rosettes
3D panels
Liquid wallpaper
Door frame
Columns and semi-columns
Moldings
Wall niches
Ornaments, panels
Fireplace panels
Pilasters
Corner elements
Brackets, consoles
Photo paintings
Texture wallpaper
Self-adhesive tiles
Decorative PVC sheet panels
WPC Decorative Wall Slats
Carpets
Floor skirting boards
Soft floor puzzle
Self-adhesive skirting board
MDF plinth
Self-adhesive carpet
Curtain rods
Window sills
Mosquito net
Photoblinds
Photo curtains
Roller blinds (roller blinds)
Sandwich panels
Window sills
Doors Omis
Liquid nails and glue
Photobed
Table tops
Table supports
Self-adhesive eco-leather
Cornices for facade
Moldings for facade
Columns, pilasters
Balustrades, balusters
Window framing
Bassages, rustics, castles
Sandriks, decor, bas-relief
Drainage systems
Soffits
Facade panels
Bathroom accessories
Kitchen accessories
Accessories for the hallway
Accessories for cosmetics
Household chemicals
Materials for street decoration
